In this article we will discuss a netplan static IP configuration on Ubuntu Linux. Netplan allows for straightforward network IP address configuration using human-readable data-serialization language YAML. The article will also discuss a default Netplan network settings and the location of the Netplan configuration file.
In this tutorial you will learn how to:
- Use netplan to set static IP on Ubuntu Server
- Configure netplan to set static IP on Ubuntu Server
Software Requirements and Conventions Used
|Category||Requirements, Conventions or Software Version Used|
|System||Any version of Ubuntu Linux system|
|Other||Privileged access to your Linux system as root or via the
|Conventions||# – requires given linux commands to be executed with root privileges either directly as a root user or by use of
$ – requires given linux commands to be executed as a regular non-privileged user
Configure static IP address using Netplan
Netplan network configuration had been first introduced starting from Ubuntu 18.04, hence Netplan is available to all new Ubuntu from this version and higher. Let’s get started with some basic understating on how netplan works on Ubuntu.
Netplan allows network configuration via both: networkd daemon or NetworkManager. networkd daemon is mainly used for server configuration, whereas NetworkManager is used by GUI users. To switch between both you need to specify
renderer explicitly via netplan configuration file.
rendereris specified within the netplan’s configuration file, then the default handler for the network configuration on this particular device will be networkd daemon.
The netplan configuration file location is set to
/etc/netplan/ directory. Other possible locations are
/run/netplan/. Depending on your Ubuntu installation the actual Netplan configuration file can take one of the following three forms:
In case you cannot find your configuration file, you may attempt to generate the new netplan config by executing the below command:
$ sudo netplan generate
Most likely your current Ubuntu system uses DHCP server to configure its networking settings. Hence, the configuration of your IP address is dynamic. In many scenarios, simply configuring your router or local DHCP server is a preferred way to set a static address to any host regardless of the operating system in use. Check your router manual and assign the static IP address to your host based on its MAC address using the DHCP service.
Netplan static ip step by step instructions
- To configure a static IP address on your Ubuntu server you need to find and modify a relevant netplan network configuration file. See the above section for all possible Netplan configuration file locations and forms.For example you might find there a default netplan configuration file called
01-netcfg.yamlwith a following content instructing the
networkddeamon to configure your network interface via DHCP:
# This file describes the network interfaces available on your system # For more information, see netplan(5). network: version: 2 renderer: networkd ethernets: enp0s3: dhcp4: yes
- To set your network interface
enp0s3to static IP address
192.168.1.1and DNS server as
220.127.116.11replace the above configuration with the one below.
You must adhere to a correct code indent for each line of the block. In other words, the number of spaces before each configuration stanza matters. Otherwise you may end up with an error message similar to:
Invalid YAML at //etc/netplan/01-netcfg.yaml line 7 column 6: did not find expected key
# This file describes the network interfaces available on your system # For more information, see netplan(5). network: version: 2 renderer: networkd ethernets: enp0s3: dhcp4: no addresses: [192.168.1.222/24] gateway4: 192.168.1.1 nameservers: addresses: [18.104.22.168,22.214.171.124]
- Once ready apply the new Netplan configuration changes with the following commands:
$ sudo netplan apply
In case you run into some issues execute:
$ sudo netplan --debug apply
This is a preferred way of setting the static IP address on Ubuntu Desktop. It is important to note the if your Ubuntu system is using Netplan to configure network on your hosts you need to set the
renderer within the Netplan’s configuraiton file to
Having the Netplan’s renderer set to
networkd daemon will result in the Wired Unmanaged error.
- Click on top right network icon and select settings corresponding to the network interface you wish to assign with the static IP address.
- Next, click on the gear box icon next to your network connection you wish to configure. This could be wired or wireless connection.
- Select IPv4 from the top menu.
- Choose Manual for the IPv4 settings, enter your desired configuration and hit Apply.
- Restart your network by ON/OFF switch.
- Check your new static IP address configuration.